DC-DC Battery Charger B2b Inverter MPPT Solar

• Rated Power: 24V-310W, 685W
• Charging Current: 12V/6A, 12V 60A
• Input Voltage: 12-24/12V, 24V(21-32V)
• Shipping Cost: Estimated freight per unit.: about shipping cost and estimated delivery time.
• Currency: US$
• Return&refunds: You can apply for a refund up to 30 days after receipt of the products.
• Model NO.: B2B241260
• Type: Lead-Acid Battery Charger, Ni-CD Battery Charger
• Charging Type: Solar Charger, Solar Charger
• Principle: Half-Bridge Charger, Intelligent Charging
• DC-DC Charge: 24V 60A
• Charge Battery Type: Gel, Sealed, Flooded, LiFePO4, Lithium-Ion
• APP: Support
• Bluetooth: Support
• MPPT Tracking Efficiency: 99.8%
• Output Voltage: 12V(10.5-16.0V)
• MPPT Solar: 12V 50A
• Pvmax: 685W
• Transport Package: Neutral
• Specification: neutral
• Trademark: Oxiang, OEM
• Origin: Shenzhen
• Production Capacity: 50000

Product Description

DC-DC Battery charger B2B inverter MPPT solar

 

 Features

This is a all-automatic DC-DC battery charger, you can use the battery (12V) to charge the battery (12V) (B2B), specially designed for RVs, exposed cars, campers, ships, etc.

Technical Data
 

cable cross section	cable length "+ Start II"	cable length with insulated construction "- Batt."	"Fuse II" cable protection	cable length "- Com." to "- Board I"	cable length "+ Board I"	"Fuse I" cable protection	cable lengths - and + "solar panels"
4mm2	_	_	_	_	_		up to 4m
6mm2	_	_	_	_	_		up to 6m
10mm 2	_	_	_	0.5-2.0m	0.5-2.0m	80A	up to 10m
16mm 2	up to 7m	up to 7m	100A	1.5-3.0m	1.5-3.0m	80A	up to 16m
25mm 2	up to 10m	up to 10m	100A	2.5-5.0m	2.5-5.0m	80A	_

 

cable cross section	cable length "+ Start II"	cable length with insulated construction "- Batt."	"Fuse II" cable protection	cable length "- Com." to "- Board I"	cable length "+ Board I"	"Fuse I" cable protection	cable lengths - and + "solar panels"
4mm2	_	_	_	_	_		up to 4m
6mm2	_	_	_	_	_		up to 6m
10mm 2	_	_	_	0.5-2.0m	0.5-2.0m	80A	up to 10m
16mm 2	up to 7m	up to 7m	100A	1.5-3.0m	1.5-3.0m	80A	up to 16m
25mm 2	up to 10m	up to 10m	100A	2.5-5.0m	2.5-5.0m	80A	_

B2B Operation

mobile operation from dynamo and starter battery (Battery to Battery):
it refers to charging the main battery through dynamo and starter battery, .If it is not used in the Vehicle , you can also use one battery (12V) to charge another

1. . The efficient charging converter (booster) allows full charging of the board battery during driving.
2. . It increases/reduces the voltage to the level, which is required for precise charging of the board battery with the optimum characteristic line of charging.
3. . The simultaneously supplied 12 V consumers are protected against overvoltage and voltage fluctuations.

Further Characteristics of the Unit
 

• The output voltage is stabilized, free of peaks, smoothed and filtered.
• Galvanic isolation between input and output:

• No overvoltage at the output and thus protection of the consumer if the ground line is lost.
• Clean, undisturbed mass ratios, even with long supply lines.
• Stable operating voltage on site in mobile operation, e.g. Containers, trailers, roll containers etc.
• Filtering and suppression of disturbances on the input to the output side.

• Fully automatic continuous operation: The DC-DC converter can constantly work with the battery
• Surveillance-free operation: multiple protection against overload, overheating, over voltage, short circuit, Misconduct and deep discharge of the battery through electronic regulation to complete
• Switch off by built-in safety switch.

Function
 

 

Security guidelines

Intended use:
The DC-DC converter was built on the basis of the valid safety guidelines. The use may only be:

1. On lead-acid, lead-gel or lead AGM or LiFePO4 batteries of the specified nominal voltage.
2. With the specified cable cross-sections for inputs and outputs.
3. With fuses of the specified strength near the battery to protect the wiring between the batteries and DC-DC converter connections.

5. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases as well as in a non-condensing environment.
The device must never be used in places where there is a risk of gas or dust explosion consists!

Installation of the Unit

1. . Install the charger near the board supply battery I (for short charging cables) at a clean, even and hard mounting surface,which is protected from moisture, humidity and aggressive battery gases. The unit can be installed in any position.
2. . To be installed in a moisture-proof, water-proof place, corrosion-proof place
3. . When the charging controller is working, the fan will bring out heat, so when installing, ensure that there is at least 10cm of space behind the charger controller
4. . Choose the appropriate cable specifications, length and fuse specifications, reverse connection of the battery will cause serious damage to the equipment

Why Choose us?

> Oxiang is located in Shenzhen, China, a new type of city in rapid development. We focus on CCTV Camera researching and manufacturing from 2006;

> Sales person provide Pre-sales and after-sales service; Professional engineers are always standby and assist offer solutions;

> Cooperate with multiple departments to complete raw material procurement, production, inspection, delivery and other steps;

> The product comes with a one-year warranty.