24V-12V B2b60A MPPT 50A Dual Input DC Solar Battery Charger Controller

• Customization: Available
• Rated Power: 24V-310W
• Charging Current: 12V/6A
• Model NO.: BS24126050
• Input Voltage: 12-24/12V
• Type: Lead-Acid Battery Charger
• Charging Type: Solar Charger
• Principle: Half-Bridge Charger
• Main Battery: 12V
• Main Battery Type: Gel, Sealed, Flooded, LiFePO4, Lithium-Ion
• Vehicle Start Battery: 24V
• Start Battery Type: Lead-Acid
• DC-DC Max. Charging Current: 60A
• Solar Max Charging Current: 50A
• Solar Max Voltage: 50V
• Self Consumption Current: 18mA
• Dimension: 190*215*77mm
• Weight: 1.6kg
• Transport Package: Neutral
• Specification: neutral
• Trademark: Oxiang, OEM
• Origin: Shenzhen
• Production Capacity: 50000
• Package Size: 32.00cm * 26.00cm * 18.00cm
• Package Gross Weight: 3.000kg

Product Description

DC-DC Battery charger B2B inverter MPPT solar

 

 Features

24V-12V Dual input DC & Solar Battery charger support Bluetooth, Free APP and Meter,Automatic smart vehicle charger,Battery to Battery

1.Input voltage:24V, Output voltage: 12V

2.B2B charge: 12V 60A

3.MPPT solar: 12V 50A;Pvmax:685W

4.Charge Battery type:GEL,Sealed,Flooded,LiFePO4,Lithium-ion

Choose Accessories: Monitor(MT-2); Bluetooth Dongle(BT10); Temperature Sensor(TRS)

Technical Data
 

	BS24126050
Main battery "BOARD I"
Lead-Acid, Gel, AGM Batteries Nominal Voltage	12V
LiFePO4 Nominal Voltage	12.8V
lithium-ion(NCM) Nominal Voltage	11.1V
Capacity (Battery Size), recommended	100-520AH
Battery voltage range	8V-16V
Vehicle Starter Battery "Start II"
Vehicle Starter Battery Nominal Voltage	24V
Capacity (Battery Size), recommended	80-100AH
B2B Charging operation
Start battery voltage range	21~32V
Max.charge power	780W
Max. chrge current	60A
"D+" signal voltage	16-32V
MPPT solar charge controller (only BS series)
Max. PV power	685W
Max. PV charge current	40A
Max. Open circuit voltage	50V
Board I Max.charge current	50A
PV charges the start battery	no function
Temperature compensation	-3mv/ºC/2V
"TR"signal	NC
Main battery temperature sensor"T T"	YES
Main battery voltage detection"SS-,SS+"	YES
Stand-by current	32±2mA
Weight	1.6kg
Operating temperature	-20-50ºC
Demension	190×215×70mm

 

Further Characteristics of the Unit
 

• The output voltage is stabilized, free of peaks, smoothed and filtered.
• Galvanic isolation between input and output:

• No overvoltage at the output and thus protection of the consumer if the ground line is lost.
• Clean, undisturbed mass ratios, even with long supply lines.
• Stable operating voltage on site in mobile operation, e.g. Containers, trailers, roll containers etc.
• Filtering and suppression of disturbances on the input to the output side.

• Fully automatic continuous operation: The DC-DC converter can constantly work with the battery
• Surveillance-free operation: multiple protection against overload, overheating, over voltage, short circuit, Misconduct and deep discharge of the battery through electronic regulation to complete
• Switch off by built-in safety switch.

Function
 

 

Security guidelines

Intended use:
The DC-DC converter was built on the basis of the valid safety guidelines. The use may only be:

1. On lead-acid, lead-gel or lead AGM or LiFePO4 batteries of the specified nominal voltage.
2. With the specified cable cross-sections for inputs and outputs.
3. With fuses of the specified strength near the battery to protect the wiring between the batteries and DC-DC converter connections.

5. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases as well as in a non-condensing environment.
The device must never be used in places where there is a risk of gas or dust explosion consists!

Installation of the Unit

1. . Install the charger near the board supply battery I (for short charging cables) at a clean, even and hard mounting surface,which is protected from moisture, humidity and aggressive battery gases. The unit can be installed in any position.
2. . To be installed in a moisture-proof, water-proof place, corrosion-proof place
3. . When the charging controller is working, the fan will bring out heat, so when installing, ensure that there is at least 10cm of space behind the charger controller
4. . Choose the appropriate cable specifications, length and fuse specifications, reverse connection of the battery will cause serious damage to the equipment

Why Choose us?

> Oxiang is located in Shenzhen, China, a new type of city in rapid development. We focus on CCTV Camera researching and manufacturing from 2006;

> Sales person provide Pre-sales and after-sales service; Professional engineers are always standby and assist offer solutions;

> Cooperate with multiple departments to complete raw material procurement, production, inspection, delivery and other steps;

> The product comes with a one-year warranty.