DC to DC Converter MPPT Solar Charge Controller Battery charger
Features
This is a all-automatic DC-DC battery charger, you can use the battery (12V) to charge the battery (12V) (B2B), specially designed for RVs, exposed cars, campers, ships, etc.
B2B126030: 12V-12V/60A BS123020: 12V-12V/30A
Technical Data
| |
|
| Main battery " Bord " |
|
| Lead-Acid, Gel, AGM Batteries Nominal Voltage |
12V |
| LiFePO4 Nominal Voltage |
12.8V |
| lithium- ion( NCM) Nominal Voltage |
11.1V |
| Capacity (Battery Size), recommended: |
45-280AH |
| Vehicle Starter Battery "Start II": |
|
| Vehicle Starter Battery Nominal Voltage: |
12V |
| Min. Battery Capacity (Size), recommended: |
60AH |
| 12 V / 12 V B2B Charging operation |
|
| Input Voltage Range "Start II" ,"D+" controlled: |
10.5-16V |
| Maximum charging power: |
650W |
| " Bord " Max. charge current |
30A |
| Activation Control Input "D+" |
8-16V |
Signal Output "OK/TR", Switch Position "TR",
Cutoff Relay Bypass/max |
12V/1A |
| Signal Output "OK/TR", Switch Position "OK" |
12V/1A |
| Input "T T" for Battery Temperature Sensor "Board I": |
YES |
| " Ss-" "Ss+" Inputs Sensor Cables "-" and "+" for Battery "Board I": |
YES |
| stand-by current |
24mA |
| Main battery overvoltage protection |
15.5V |
| weight |
1.44kg |
| demension |
190×194×70mm |
| Operating temperature |
-20-50ºC |
B2B Operation
mobile operation from dynamo and starter battery (Battery to Battery):
it refers to charging the main battery through dynamo and starter battery, .If it is not used in the Vehicle , you can also use one battery (12V) to charge another
- . The efficient charging converter (booster) allows full charging of the board battery during driving.
- . It increases/reduces the voltage to the level, which is required for precise charging of the board battery with the optimum characteristic line of charging.
- . The simultaneously supplied 12 V consumers are protected against overvoltage and voltage fluctuations.
Further Characteristics of the Unit
- The output voltage is stabilized, free of peaks, smoothed and filtered.
- Galvanic isolation between input and output:
- No overvoltage at the output and thus protection of the consumer if the ground line is lost.
- Clean, undisturbed mass ratios, even with long supply lines.
- Stable operating voltage on site in mobile operation, e.g. Containers, trailers, roll containers etc.
- Filtering and suppression of disturbances on the input to the output side.
- Fully automatic continuous operation: The DC-DC converter can constantly work with the battery
- Surveillance-free operation: multiple protection against overload, overheating, over voltage, short circuit, Misconduct and deep discharge of the battery through electronic regulation to complete
- Switch off by built-in safety switch.
Security guidelines
Intended use:
The DC-DC converter was built on the basis of the valid safety guidelines. The use may only be:
- On lead-acid, lead-gel or lead AGM or LiFePO4 batteries of the specified nominal voltage.
- With the specified cable cross-sections for inputs and outputs.
- With fuses of the specified strength near the battery to protect the wiring between the batteries and DC-DC converter connections.
5. In a well-ventilated room, protected against rain, moisture, dust and aggressive battery gases as well as in a non-condensing environment.
The device must never be used in places where there is a risk of gas or dust explosion consists!
Installation of the Unit
- . Install the charger near the board supply battery I (for short charging cables) at a clean, even and hard mounting surface,which is protected from moisture, humidity and aggressive battery gases. The unit can be installed in any position.
- . To be installed in a moisture-proof, water-proof place, corrosion-proof place
- . When the charging controller is working, the fan will bring out heat, so when installing, ensure that there is at least 10cm of space behind the charger controller
- . Choose the appropriate cable specifications, length and fuse specifications, reverse connection of the battery will cause serious damage to the eq
Why Choose us?
> Oxiang is located in Shenzhen, China, a new type of city in rapid development. We focus on CCTV Camera researching and manufacturing from 2006;
> Sales person provide Pre-sales and after-sales service; Professional engineers are always standby and assist offer solutions;
> Cooperate with multiple departments to complete raw material procurement, production, inspection, delivery and other steps;
> The product comes with a one-year warranty.
){kind=link}
){kind=link}